What blade cuts rigid insulation board without dust?

A bandknife with a wavy or scallop edge. The continuous knife edge slices through rigid board in one pass rather than sawing at it, so there is no tooth action to tear the cell structure or throw dust. The profiled edge also bites into slippery facings and layered product that a plain edge can slide over.

What do I need for cutting rockwool and mineral wool batts?

A wavy edge bandknife is the place to start. Fibrous batts compress under a plain edge, which crushes and drags the fibres, where the wavy profile grips the surface and starts the cut cleanly. Tell us the machine and the batt density and we will match the edge and weld the band to your loop length.

What blade for a line that runs mixed foam and insulation grades?

A scallop edge bandknife is the usual answer, because one edge form covers the span from soft and memory foam up to rigid foam, insulation and packaging. That saves changing bands between jobs. If fibrous mineral wool is in the mix, plan on wire for those batts rather than forcing them through a knife.

Material guide

Insulation cutting blades and wire

Rigid PIR boards and layered product want an edge that bites rather than skates. Wavy and scallop bandknives slice rigid and layered insulation dust-free with a clean face, welded to your machine's loop length in the UK.

Shop bandknife blades Find my blade

The problem with cutting insulation

Insulation is not one material. Rigid PIR board, layered composite product and fibrous rockwool batts behave differently under an edge. A blade chosen for one will misbehave in the others. A toothed bandsaw blade tears at foam and fibre rather than cutting it: the teeth rip the cell structure, throw dust into the air and the machine and leave a ragged face that spoils the board.

Rigid and layered product punishes the wrong knife edge too. A plain straight edge can skate over slippery facings and compressed layers instead of biting in, wandering off line before the cut has properly started. A wavy or scallop bandknife edge grips the surface and slices through in a single dust-free pass, leaving a clean face.

Fibrous mineral wool is different again. It compresses under a blade rather than presenting a solid face to cut, so a plain edge crushes and drags the fibres instead of parting them. A profiled wavy edge grips the surface and starts the cut cleanly, keeping torn faces and waste to a minimum.

Recommended blades for insulation

Constructions and ranges from the manufacturers' published data, with the honest reason each blade makes the list. Every one is welded to your machine's length.

Recommended blades for insulation, drawn from the manufacturers' published ranges. Prices are from prices per welded loop, ex VAT, at the narrowest width and shortest length.
Blade	Construction	Width range	Why this blade	From price
Slicer37 Wavy Band Knife BladeDakin-Flathers Slicer37	Thin, toothless or lightly toothed continuous knife edgeBandknife Blades guide	10mm to 32mm	The wavy edge bites into slippery and layered insulation that a straight edge can skate over, cutting dust-free with a continuous knife edge.	From £30.50 ex VATsample pricing
Slicer37 Scallop Bandknife BladeDakin-Flathers Slicer37	Thin, toothless or lightly toothed continuous knife edgeBandknife Blades guide	10mm to 25mm	Its scallop edge spans low density and memory foam up to rigid foam and insulation, so one edge form covers lines running mixed grades.	From £30.50 ex VATsample pricing

Getting the cut right

General rules that hold across machines. Exact widths, pitches and options are on each product page.

Match the edge to the product
Rigid PIR and layered boards want a wavy or scallop bandknife: the profiled edge bites into slippery facings that a straight edge skates over. The wavy edge also handles fibrous and layered product, gripping the surface so the cut starts cleanly rather than crushing the material. Choose by what is on the table, not by habit.
Let the edge do the work
A bandknife slices rather than saws. Forcing the feed compresses the board ahead of the edge, deflects the thin band and leaves a stepped or torn face. Feed steadily and let the edge part the material at its own pace. The same discipline applies to wire: tension does the cutting, not pressure.
Keep the band tensioned and tracked
A bandknife is thin and flexible by design, so it relies on the machine for its stiffness. Check tension and tracking before a run: a slack or badly tracked band wanders in the cut and produces wedge-shaped slices. On wire machines the same rule applies, since an under-tensioned wire bows away from the cut line in dense product.
Order to your machine's length
Bandknives run as welded loops, so measure the loop length from the machine manual or an old band rather than guessing. The wavy bandknife is published in widths from 10 to 32mm and the scallop from 10 to 25mm; fit the size your machine was built to run and we weld the band to length in the UK.

Suggested image

Action shot: recommended blade cutting insulation, cut face visible

materials/insulation/cutting

Industry guide

Foam, Insulation and Packaging Conversion

Cutting insulation for a living? The industry guide maps the whole workload, not just this material.

Read the guide

Other material guides

Frequently asked questions

Tell the wizard your machine and length and it will match insulation to a blade that fits.

Find my blade